| Terminal Symbol | Terminal Name |
|---|---|
| R/L1, S/L2, T/L3 | Main power supply input terminals * 1-phase 200V class : Connect a [R/L1] and [T/L3] terminal. * 1-phase 100V class : Connect a [R/L1] and [N] terminal. |
| U/T1, V/T2, W/T3 | Inverter output terminals |
| PD/+1, P/+ | DC reactor connection terminals |
| P/+, RB | External braking resistor connection terminals |
| P/+, N/- | External braking unit connection terminals |
| G | Ground connection terminal |
| Terminal | Model | Screw Diameter |
|---|---|---|
 |
001～007LF 001～004SF 004MF |
M3.5 |
| 015～037LF 007～022SF 004～040HF 007MF |
M4 | |
 |
055～075LF 055～075HF |
M5 |
| 110LF 110～150HF |
M6 | |
| 150LF | M8 |
| Switch Name | Switch Name Description |
|---|---|
| (1)Termination resistor selection switch | Termination resistor change by side switch of the terminal RS-485 of the control circuit terminals. WJ200 has a built-in 200 Ω resistor activated by a dip switch. |
| (2)Safe stop function selection switch | To enable the Safe stop function, set the slide lever of slide switch ON. Before operating slide switch, make sure that the input power supply is off. |
| (3)EDM function selection switch |
To enable the EDM function, set the slide lever of slide switch ON. Before operating slide switch, make sure that the input power supply if off. |
Sink or source logic is switched by a short bar as below.
Sink logic
Source logic
| Terminal Name |
Description | Ratings | |||
|---|---|---|---|---|---|
| Analog | Power Supply |
L | GND for analog signals | Sum of [OI], [O], and [H] currents (return) |
|
| H | +10V analog reference | 10VDC nominal, 10mA max. | |||
| Frequency Setting |
O | Analog voltage input | 0 to 9.8 VDC range, 10 VDC nominal, input impedance 10 kW | ||
| OI | Analog current input | 4 to 19.6 mA range, 20 mA nominal, input impedance 250 W | |||
| Sensor input | PTC(5) | Motor thermistor input | Connect motor thermistor between PTC and L terminal to detect the motor temperature. Set 19 in C005 | ||
| Monitor Output | AM | Analog voltage output | 0~10VDC 1mA maximum | ||
| Digital | Power Supply | L | GND for logic inputs | Sum of input [1]~[7] currents (return) | |
| P24 | +24V for logic inputs | 24VDC, 30mA. (do not short to terminal L) | |||
| PLC | Intelligent input common | Factory set: Source type for –FE and –FU models (connecting [P24] to [1]~[7] turns each input ON). To change to sink type, remove the short bar between [PLC] and [L], and connect it between [P24] and [L]. In this case, connecting [L] to [1]~[7] makes each input ON. | |||
| Input | Contact | 1 2 3 4 5 6 7 |
Discrete logic inputs (Terminal [3],[4],[5] and [7] have dual function. See following description and related pages for the details.) |
[Input ON condition] Voltage between each terminal and PLC: DC 18V min. [Input OFF condition] Voltage between each terminal and PLC: DC 3V max. Allowable maximum voltage between each terminal and PLC: DC 27VDC max. (use PLC or an external supply referenced to terminal L) |
|
| GS1(3) | Safe stop input GS1 | Functionality is based on ISO13849-1 |
|||
| GS2(4) | Safe stop input GS2 | ||||
Pulse |
EB(7) | Pulse train input B | 2kHz max. Common is [PLC] | ||
| EA | Pulse train input A | 32kHz max. Common is [L] | |||
| Output | Open collector | 11/EDM | Discrete logic outputs [11] (Terminal [11] has dual function. See following description and related pages for the details.) |
50mA max. ON state current, 27 VDC max. OFF state voltage Common is CM2 In case the EDM is selected, the functionality is based on ISO13849-1 4VDC max. ON state voltage depression |
|
| 12 | Discrete logic outputs [12] | 50mA max. ON state current, 27 VDC max. OFF state voltage Common is CM2 |
|||
| CM2 | GND for logic output | 100 mA: [11], [12] current return | |||
| Pulse | EO | Pulse train output | 10VDC 2mA maximum 32kHz maximum |
||
Relay |
AL0 | Relay common contact | 250VAC, 2.5A (R load) max. 250VAC, 0.2A (I load, P.F.=0.4) max. 100VAC, 10mA min. 30VDC, 3.0A (R load) max. 30VDC, 0.7A (I load, P.F.=0.4) max. 5VDC, 100mA min. |
||
| AL1 | Relay contact, normally open | ||||
| AL2 | Relay contact, normally closed | ||||
| Serial communication port | SP, SN | Serial communication terminal | For RS485 Modbus communication. | ||
Search
Global
